In very early versions routed CHILD_SAs were attached to IKE_SAs, since
that's not the case anymore (they are handled via trap manager), we can
remove this special handling.
This algorithm uses a fixed-length key and we MUST NOT send a key length
attribute when proposing such algorithms.
While we could accept transforms with key length this would only work as
responder, as original initiator it wouldn't because we won't know if a
peer requires the key length. And as exchange initiator (e.g. for
rekeyings), while being original responder, we'd have to go to great
lengths to store the condition and modify the sent proposal to patch in
the key length. This doesn't seem worth it for only a partial fix.
This means, however, that ChaCha20/Poly1305 can't be used with previous
releases (5.3.3 an newer) that don't contain this fix.
Fixes#2614.
Fixes: 3232c0e64e ("Merge branch 'chapoly'")
Since these are installed overlapping (like during a rekeying) we have to use
the same (unique) marks (and possibly reqid) that were used previously,
otherwise, the policy installation will fail.
Fixes#2610.
If the responder is behind a NAT that remaps the response from the
statically forwarded port 500 to a new external port (as Azure seems to be
doing) we should still switch to port 4500 if we used port 500 so far as
it would not have been possible to send any messages to it if it wasn't
really port 500 (we only add a non-ESP marker if neither port is 500).
This helps to distinguish between port and protocol if only one of them
is set. If no protocol is set it's printed as 0, if the traffic
selector covers any port (0-65535) the slash that separates the two values
and the port is omitted.
If a Quick mode is initiated for a CHILD_SA that is already installed
we can identify this situation and rekey the already installed CHILD_SA.
Otherwise we end up with several CHILD_SAs in state INSTALLED which
means multiple calls of child_updown are done. Unfortunately,
the deduplication code later does not call child_updown() (so up and down
were not even).
Closesstrongswan/strongswan#95.
Until now the configuration available to user for HW offload were:
hw_offload = no
hw_offload = yes
With this commit users will be able to configure auto mode using:
hw_offload = auto
Signed-off-by: Adi Nissim <adin@mellanox.com>
Reviewed-by: Aviv Heller <avivh@mellanox.com>
Until now there were 2 hw_offload modes: no/yes
* hw_offload = no : Configure the SA without HW offload.
* hw_offload = yes : Configure the SA with HW offload.
In this case, if the device does not support
offloading, SA creation will fail.
This commit introduces a new mode: hw_offload = auto
----------------------------------------------------
If the device and kernel support HW offload, configure
the SA with HW offload, but do not fail SA creation otherwise.
Signed-off-by: Adi Nissim <adin@mellanox.com>
Reviewed-by: Aviv Heller <avivh@mellanox.com>
If a daemon PID file references the process that does the check, it is safe
to ignore it; no running process can have the same PID. While this is rather
unlikely to get restarted with the same PID under normal conditions, it is
quite common when running inside PID namespaced containers: If a container
gets stopped and restarted with a PID file remaining, it is very likely that
the PID namespace assigns the same PID to our service, as they are assigned
sequentially starting from 1.
According to RFC 5114 the exponent length for these groups should always equal
the size of their prime order subgroup.
This was handled correctly before the initialization was done during
library initialization.
Fixes: 46184b07c1 ("diffie-hellman: Explicitly initialize DH exponent sizes during initialization")
The previous code was obviously incorrect and caused strange side effects
depending on the compiler and its optimization flags (infinite looping seen
with GCC 4.8.4, segfault when destroying the private key in build() seen
with clang 4.0.0 on FreeBSD).
Fixes#2579.
We can't use ASN1_DEF, which would technically be more correct, as the
ASN.1 parser currently can't handle that. For algorithm identifiers we
often use ASN1_EOC as type (with ASN1_RAW), however, that doesn't work with
ASN1_DEF because the element is assumed missing if the type doesn't match.
On the other hand, we can't set the type to ASN1_SEQUENCE because then the
parser skips the following rule if the element is missing (it does so for
all constructed types, but I guess is mainly intended for context tags),
which in this case overruns the parser rules array.
This way there will be a mismatch if one of the proposals contains
transform types not contained in the other (the fix list of transform
types used previously resulted in a match if unknown transform types
were contained in one of the proposals). Merging the sets of types
makes comparing proposals with optional transform types easier (e.g.
DH for ESP with MODP_NONE).
Tobias Brunner