Don't add a selector to tunnel mode SAs, these might serve multiple
traffic selectors but with only one selector on the SA only the traffic
matching the first one would actually get tunneled.
When using auto=route, current xfrm_acq_expires default value
implies that tunnel can be down for up to 165 seconds, if
other peer rejected first IKE request with an AUTH_FAILED or
NO_PROPOSAL_CHOSEN error message. These error messages are
completely normal in setups where another application
pushes configuration to both strongSwans without waiting
for acknowledgment that they have updated their configurations.
This patch allows strongswan to override xfrm_acq_expires default
value by setting charon.plugins.kernel-netlink.xfrm_acq_expires in
strongswan.conf.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Commit 940e1b0f66 "Filter ignored
interfaces in kernel interfaces (for events, address enumeration,
etc.)" made charon to ignore routes with unusable interfaces.
Unusable interface is one where charon has not seen RTM_NEWLINK
message from the kernel.
Sometime RTM_NEWLINK message can be 1048 bytes large. This is
24 bytes more than currently allocated buffer of 1024 bytes.
If kernel sends such a large message, then it would be silently
ignored by charon and corresponding interface would never become
usable. Hence strongSwan might resolve invalid source IP address
in get_route() function. This would prevent IPsec tunnel to be
established.
To reproduce create a VLAN interface with following command:
vconfig add eth1 12
If multiple roam events are triggered within ROAM_DELAY, only one job is
created. The old code set the address flag to the value of the last
triggering call. So if a route change followed an address change within
ROAM_DELAY the address change was missed by the upper layers, e.g. causing
it not to update the list of addresses via MOBIKE.
The new code now keeps the state of the address flag until the job is
actually executed, which still has some issues. For instance, if an
address disappears and reappears within ROAM_RELAY, the flag would not
have to be set to TRUE. So address updates might occasionally get
triggered where none would actually be required.
Fixes#374.
INCLUDES are now deprecated and throw warnings when using automake 1.13.
We now also differentiate AM_CPPFLAGS and AM_CFLAGS, where includes and
defines are passed to AM_CPPFLAGS only.
If a transport/BEET SA has different selectors for different proto/ports,
installing just the proto/port of the first SA would break any additional
selector.
Previously we silently replaced an existing policy with a new one if the
reqid changed for the same selectors. This will break an old policy in the
favour of the new one (for example if two clients behind the same NAT use
transport mode).
With this change any new policy gets rejected if the reqid differs. This will
make sure we break no existing policy. For rekeying and acquires we still can
have overlapping policies (as we use the same reqid), but for unrelated
connections this is not true anymore (it wasn't actually before, we just
silently broke the existing policy).
This new flag gives the kernel-interface a hint how it should priorize the
use of newly installed SAs during rekeying.
Consider the following rekey procedure in IKEv2:
Initiator --- Responder
I1 -------CREATE-------> R1
I2 <------CREATE--------
-------DELETE-------> R2
I3 <------DELETE--------
SAs are always handled as pairs, the following happens at the SA level:
* Initiator starts the exchange at I1
* Responder installs new SA pair at R1
* Initiator installs new SA pair at I2
* Responder removes old SA pair at R2
* Initiator removes old SA pair at I3
This makes sure SAs get installed/removed overlapping during rekeying. However,
to avoid any packet loss, it is crucial that the new outbound SA gets
activated at the correct position:
* as exchange initiator, in I2
* as exchange responder, in R2
This should guarantee that we don't use the new outbound SA before the peer
could install its corresponding inbound SA.
The new parameter allows the kernel backend to install the new SA with
appropriate priorities, i.e. it should:
* as exchange inititator, have the new outbound SA installed with higher
priority than the old SA
* as exchange responder, have the new outbound SA installed with lower
priority than the old SA
While we could split up the SA installation at the responder, this approach
has another advantage: it allows the kernel backend to switch SAs based on
other criteria, for example when receiving traffic on the new inbound SA.
Bring some extensions to eap-radius, namely a virtual IP address provider based
on received Framed-IPs, forwarding of Cisco Unity banners, Interim Accounting
updates and the reporting of sent/received packets.
Installs bypass policies for the physical address if a virtual address is
assigned, and installs a proper source route to actually use the physical
address for bypassed destinations.
Conflicts:
src/libcharon/plugins/unity/unity_handler.c
Martin Willi