If a policy with IPComp template triggers an acquire, we get two, one for
an IPComp, one for ESP/AH SA. However, the triggering template of the trap
policy (where we get the reqid from), will be the same in both acquires,
IPComp, which we ignore, so no acquire was actually forwarded.
Such routes with a gateway that equals the peer's address are problematic
on FreeBSD. And since there is most likely a narrow route for the local
subnet anyway, the exclude routes would be redundant.
When installing routes based on remote traffic selectors, it can be
necessary to install an exclude route for the remote peer to avoid a
routing loop and continue to be able to reach it via IKE/ESP.
However, such routes are only necessary, if the routes we install don't
go via outbound interface. That's the case when using VIPs and routing
via TUN devices, or when using internal source IPs and routing via
their interfaces.
Installing such exclude routes if not necessary can cause issues on
FreeBSD (EINVAL when sending packets to the peer).
RFC3779 requires to validate the addrblocks of issuer certificates strictly,
that is, they must contain the extension and the claimed addrblock, up to
the root CA.
When working with third party root CAs that do not have the extension,
this makes using the plugin impossible. So add a depth setting that limits
the number of issuer certificates to check bottom-up towards the root CA.
A depth value of 0 disables any issuer check, the default value of -1
checks all issuers in the chain, keeping the existing behavior.
Closesstrongswan/strongswan#860
Without this, the authentication succeeded if the server sent an early
EAP-Success message for mutual, key-generating EAP methods like EAP-TLS,
which may be used in EAP-only scenarios but would complete without server
or client authentication. For clients configured for such EAP-only
scenarios, a rogue server could capture traffic after the tunnel is
established or even access hosts behind the client. For non-mutual EAP
methods, public key server authentication has been enforced for a while.
A server previously could also crash a client by sending an EAP-Success
immediately without initiating an actual EAP method.
Fixes: 0706c39cda ("added support for EAP methods not establishing an MSK")
Fixes: CVE-2021-45079
The default MTU of 1500 is too high if kernel-libipsec is used (considering
the overhead of UDP-encapsulated ESP), but might also have an effect if
a TUN device is only used to install a virtual IP (the route points to it,
so the system might use its MTU and 1500 would still be too high).
This also works around an issue on macOS 12 where no RTM_IFINFO event
is sent for the newly created TUN device (neither for the creation,
setting it "up", nor adding the address). Changing the MTU, however,
triggers such an event and we can detect the virtual IP.
Closesstrongswan/strongswan#707
If two threads are waiting in find_entry() and remove_entry(),
respectively, and the former is woken first, the latter remains stuck
as it won't get signaled.
If there are threads waiting in find_entry() and one in remove_entry()
and the latter is woken first by a thread calling put_entry(), the
former threads would remain stuck as they get never signaled.
This can happen if an IKE_SA is terminated forcefully shortly before
terminating the daemon. The thread that handles the terminate command
will call checkin_and_destroy(), which unregisters the IKE_SA from the
manager before destroying it. The main thread that calls flush() on the
IKE_SA manager won't wait for this SA (its entry is already gone), so
the processor and in turn the watcher job/thread might get canceled
before the first thread started deleting the VIP. It would then wait
indefinitely for a signal that can never be sent.
There is still a small chance the thread hangs in wait() if the state check
happens right before the watcher is canceled and it wasn't yet able to
deliver the event from the kernel, we counter that by rechecking the state
after a while.
This now includes all key material derived for IKE_SAs in the order
defined in the RFC:
{SK_d | SK_ai | SK_ar | SK_ei | SK_er | SK_pi | SK_pr}
= prf+ (SKEYSEED, Ni | Nr | SPIi | SPIr)
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com>
Wireshark doesn't really support it, but this way it at least decodes
the ESP packets correctly and the encryption keys are saved and the
packets can be decrypted. The full-length versions of SHA-384 and
SHA-512 are not supported by Wireshark as 256-bit is the longest ICV
it is able to decode currently.
The previous approach would lead to additional zero prefixes in the
encoding of the serial (which is a positive integer, not an arbitrary
blob).
Fixes#3667.
Tobias Brunner