If we have to remove and reinstall SAs for address updates (as with the
Linux kernel) there is a short time where there is no SA installed. If
we keep the policies installed they (or any traps) might cause acquires
and temporary kernel states that could prevent the updated SA from
getting installed again.
This replaces the previous workaround to avoid plaintext traffic leaks
during policy updates, which used low-priority drop policies.
This can be useful if routing rules (instead of e.g. route metrics) are used
to switch from one to another interface (i.e. from one to another
routing table). Since we currently don't evaluate routing rules when
doing the route lookup this is only useful if the kernel-based route
lookup is used.
Resolvesstrongswan/strongswan#88.
The counter does not tell us what task is actually queued, so we might
ignore the response to an update (with NAT-D payloads) if only an address
update is queued.
Instead of destroying the new task and keeping the existing one we
update any already queued task, so we don't loose any work (e.g. if a
DPD task is active and address update is queued and we'd actually like
to queue a roam task).
According to RFC 3748 MSKs must be at least 64 bytes, however, that's
not the case for the MSK derived via EAP-MSCHAPv2. The two key parts
received are only 16 bytes each (derived according to RFC 3079,
section 3.3), so we end up with an MSK of only 32 bytes. The eap-mschapv2
plugin, on the other hand, pads these two parts with 32 zeros.
Interestingly, this is not a problem in many cases as the SHA1/2 based
PRFs used later use a block size that's >= 64 bytes, so the shorter MSK
is just padded with zeros then. However, with AES-XCBC-PRF-128, for
instance, which uses a block size of 16 bytes, the different MSKs are an
issue as XCBC is applied to both to shorten them, with different results.
This eventually causes the authentication to fail if the client uses a
zero-padded MSK produced by the eap-mschapv2 plugin and the server the 32
byte MSK received via RADIUS.
This is currently not an issue for CHILD_SA rekeying tests as these only
check rekeyings of the CHILD_SA created with the IKE_SA, i.e. there is
no previous DH group to reuse.
For the CHILD_SA created with the IKE_SA the group won't be set in the
proposal, so we will use the first one configure just as if the SA was
created new with a CREATE_CHILD_SA exchange. I guess we could
theoretically try to use the DH group negotiated for IKE but then this
would get a lot more complicated as we'd have to check if that group is
actually contained in any of the CHILD_SA's configured proposals.
This way we get proper error handling if the DH group the peer requested
is not actually supported for some reason (otherwise we'd just retry to
initiate with the configured group and get back another notify).
This fixes two issues, one is a bug if a DH group is configured for the
local ESP proposals and charon.prefer_configured_proposals is disabled.
This would cause the DH groups to get stripped not from the configured but
from the supplied proposal, which usually already has them stripped. So
the proposals wouldn't match. We'd have to always strip them from the local
proposal. Since there are apparently implementations that, incorrectly, don't
remove the DH groups in the IKE_AUTH exchange (e.g. WatchGuard XTM25
appliances) we just strip them from both proposals. It's a bit more lenient
that way and we don't have to complicate the code to only clone and strip the
local proposal, which would depend on a flag.
References #2503.
IKE_SAs newly created via HA_IKE_ADD message don't have any IKE or peer
config assigned yet (this happens later with an HA_IKE_UPDATE message).
And because the state is initially set to IKE_CONNECTING the roam() method
does not immediately return, as it later would for passive HA SAs. This
might cause the check for explicitly configured local addresses to crash
the daemon with a segmentation fault.
Fixes#2500.
In scenarios where the server accepts client certificates from dozens or
even hundreds of CAs it might be necessary to omit certificate request
payloads from the IKE_SA_INIT response to avoid fragmentation.
As it is rarely the case in road-warrior scenarios that the server
already has the client certificate installed it should not be a problem
to always send it.
Depending on the plugins that eventually parse the certificate and CRL,
serials with MSB set (i.e. negative numbers that have a zero byte prefixed
when encoded as ASN.1 INTEGER) might have (x509 plugin) or not have
(openssl plugin) a zero byte prefix when returned by get_serial() or
enumerated from the CRL. Strip them before doing the comparison or
revocation checking might fail if not both credentials are parsed by the
same plugin (which should be rare and only happen if parsing of either
cert or CRL fails with one of the plugins and there is a fallback to the
implementation provided by the other plugin).
Fixes#2509.
Reset errno to 0 before calling strtoul() since it sets errno only on
error cases. So the following test fails even on correct conversions if
errno had a value != 0.
Fixes#2506.
Otherwise, the remote identity is ignored when matching owner identities
of PSKs and this way matching PSKs that explicitly have %any assigned is
improved.
Fixes#2497.
If users want to associate secrets with any identity, let 'em. This is
also possible with vici and might help if e.g. the remote identity is
actually %any as that would match a PSK with local IP and %any better
than one with local and different remote IP.
Fixes#2497.
Use argument evaluation provided by settings_t instead of using strings
to enumerate key/values.
If section names contain dots the latter causes the names to get split
and interpreted as non-existing sections and subsections.
This currently doesn't work for connections and their subsections due to
the recursion.
libnm-glib is deprecated for several years and reaching the end of its
life. Let's switch to the more up-to-date library.
Closesstrongswan/strongswan#85.
Support for mark=%unique/%unique-dir is implemented by using designated
magic mark values.
Use of masks is orthogonal to the 'unique' feature, as it is useful to be
able to designate portions of the packet mark for other purposes, while
still using different marks for different connections.
When these magic values are masked, their magic meaning is lost.
Perform masking only on explicit mark values.
Closesstrongswan/strongswan#87.
Tobias Brunner